Cables
Round shielded cables with D-Sub connectors
Shielded round cables are designed to connect daughter boards for signal conditioning and terminal boards to DAQ cards.
The cables are supplied in a standard length of 1.8m with one male and one female connectors with 1:1 wiring topology.
Note: Custom cables can be delivered up to 10 meters in length.
| CAB-0911/2 | round shielded cable D-Sub 9 (female), D-Sub 9 (male), length 1.8 m, 1:1 connectors pin wiring connection, weight approx. 120 g, packed in a plastic bag |
| CAB-2511/2 | round shielded cable D-Sub 25 (female), D-Sub 25 (male), length 1.8 m, 1:1 connectors pin wiring connection, weight approx. 220 g, packed in a plastic bag |
Flat unshielded cables with D-Sub connectors
Flat cables with D-Sub connectors are especially designed for appliacation where variable length cables are required or more than two connectors on the cable. For example, when installing daughter boards into cabinets with short interconnect cables.
The disadvantage of flat cables is the absence of shielding, so these cables should be as short as possible.
| CAB-0911X | flat cable D-Sub 9 (female), D-Sub 9 (male), length 5 cm, 1:1 connectors pin wiring connection, weight approx. 15 g, packed in a plastic bag |
| CAB-2511X | flat cable D-Sub 25 (female), D-Sub 25 (male), length 5 cm, 1:1 connectors pin wiring connection, weight approx. 30 g, packed in a plastic bag |
| CAB-2512X | flat cable D-Sub 25 (female), 2x D-Sub 25 (male), length 10 cm, 1:1 connectors pin wiring connection, weight approx. 40 g, packed in a plastic bag, (e.g. for connecting two OPT-830B boards to the DAQ card) |
| CAB-2513X | flat cable D-Sub 25 (female), 3x D-Sub 25 (male), length 15 cm, 1:1 connectors pin wiring connection, weight approx. 50 g, packed in a plastic bag, (e.g. for connecting three OPT-830B boards to the DAQ card) |
| CAB-2514X | flat cable D-Sub 25 (female), 4x D-Sub 25 (male), length 20 cm, 1:1 connectors pin wiring connection, weight approx. 60 g, packed in a plastic bag, (e.g. for connecting four OPT-830B boards to the DAQ card) |
Flat unshielded cables with dual-row connectors
Flat cables with dual-row connectors are especially designed for interconnection of signal conditioning boards inside the cabinets. They are also used to interconnection DIO signals between adaptors with mounting bracket and pin-headers connectors located on rear edge of DAQ cards.
Cables combining dual-row connectors and D-Sub connectors are also used to interconnection analog isolation amplifiers boards OPT-1020/1120.
| CAB-1011/03 | 10-wire flat cable, dual-row connectors at both ends, length 30 cm, weight approx. 10 g, packed in a plastic bag (e.g. replacing cables supplied with PCE-16xx if the PCE-16xx board is not located next to the DAQ card) |
| CAB-1004C | 10-wire flat cable, 4x dual-row connectors (spacing 40 mm), 1x D-Sub 9 (female) at the other end of cable, length 20 cm, weight approx. 20 g, packed in a plastic bag (e.g. for connecting up to four OPT-1020/1120 daughter boards to the power supply) |
| CAB-1008C | 10-wire flat cable, 8x dual-row connectors (spacing 40 mm), 1x D-Sub 9 (female) at the other end of cable, length 40 cm, weight approx. 35 g, packed in a plastic bag (e.g. for connecting up to four OPT-1020/1120 daughter boards to the power supply) |
| CAB-2604C | 26-wire flat cable, 4x dual-row connectors (spacing 40 mm), 1x D-Sub 25 (female) at the other end of cable, length 20 cm, weight approx. 40 g, packed in a plastic bag (e.g. for connecting up to four OPT-1020/1120 daughter boards to the DAQ card) |
| CAB-2608C | 26-wire flat cable, 8x dual-row connectors (spacing 40 mm), 1x D-Sub 25 (female) at the other end of cable, length 40 cm, weight approx. 65 g, packed in a plastic bag (e.g. for connecting up to eight OPT-1020/1120 daughter boards to the DAQ card) |
Other cables
In addition to the cables described above, a wide range of other types and cables with different length can be supplied.